DPA 3511ES
d:dicate™ Stereo Kit with 4011ES Cardioid Mics

OUR PART #  3511ES

A complete stereo mic kit, the 3511ES from DPA Microphones features 2 compact d:dicate 4011ES Cardioid Microphones with active side cables. They're ultra-compact cardioid microphones that are part of DPA's modular d:dicate Microphone Series. Meticulously factory-matched within +/- 1 dB on frequency response as well as sensitivity over their entire frequency bandwidth, these mics work great for unobtrusive spot-miking, such as hanging or table use. Each mic is only 3.5cm (1.4") in length, and has a low-key appearance. In addition, each mic features an integrated cable solution which allows you to hang it from the ceiling and create precise and repeatable positions and angles when spot-miking orchestra sections or atmospheric ambience.

The DPA 4011 Cardioid Microphone
The principal appeal of the 4011 is its directional quality and attention to detail. Its transparent  sound reproduction keeps everything sounding like the original. Its first-order cardioid polar pickup pattern delivers exceptional separation between sound sources. The 4011 is as equally suited for close-up work on acoustic guitar, grand piano, wind instruments, percussion, overheads, and vocals, as it is for spot-miking symphonies, and it can adeptly handle incredibly high sound levels as well. It features a flat on-axis frequency response and superb phase response that provides a totally faithful reproduction of the original sound. Its off-axis response is similarly smooth, so that any leakage is still a precise reflection of the original, though attenuated based upon its true first-order cardioid pickup pattern characteristics.

DPA Microphones 3511ES Features:

  • Close-miking
  • Great for high sound levels
  • Factory-matched pair within +/- 1 dB
  • Accurate sound
  • Colorless sound
  • Modular flexibility

DPA Microphones 3511ES Specifications:

  • Directional Pattern: Cardioid
  • Principle of operation: Pressure gradient
  • Cartridge type: Pre-polarized condenser
  • Frequency range: 20 Hz - 20 kHz
  • Frequency range, +/- 2 dB, at 30 cm (11.8"): 40 Hz -20 kHz
  • Sensitivity, nominal, +/- 2 dB at 1 kHz: 10 mV/Pa; -40dB re. 1 V/Pa
  • Equivalent noise level, A-weighted: Typ. 18 dB(A) re.20 µPa (max. 20 dB(A))
  • Equivalent noise level, ITU-R BS.468-4: Typ. 25 dB
  • S/N ratio (A-weighted), re. 1 kHz at 1 Pa (94 dB SPL): Typ. 76 dB(A)
  • Total harmonic distortion (THD): < 1% up to 139 dB SPL peak
  • Dynamic range: Typ. 121 dB
  • Max. SPL, peak before clipping: 144 dB
  • Output impedance: 100 Ohms
  • Minimum load impedance: 2 kOhms
  • Cable drive capability: 100 m (328 ft)
  • Output balance principle: Impedance balancing
  • Common mode rejection ratio (CMRR): > 40 dB
  • Power supply (for full performance): 48 V Phantom power (+/- 4 V)
  • Current consumption: 3.5 mA
  • Connector:
    • XLR-3M
      • Pin 1: shield
      • Pin 2: signal + phase
      • Pin 3: - phase
  • Color: Matte black
  • Weight: 109 g (3.8 oz)
  • Microphone diameter: 19 mm (0.75 in)
  • Capsule diameter: 19 mm (0.75 in)
  • Microphone length: 35 mm (1.38 in)
  • Maximum output voltage, RMS: 2.2 V
  • Polarity: +V at pin 2 for positive sound pressure
  • Temperature range: -40° F to 113° F (-40° C to 45° C)
  • Relative humidity (RH): Up to 90%
  • Matching tolerance (frequency response and sensitivity): +/- 1 dB
  • Phase deviation for kit: < 10°
Add to Cart

We're sorry, only of this item available

Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM