Leviton RMB81-112
8-Gang Remembrance DMX Station - Master & 12 Sliders

OUR PART #  RMB81-112

NOTE: In lieu of an available picture of the RMB81-112, a similar model is shown above.

Leviton RMB81-112 Features:

  • Local creation of new presets with the integral scene master set up/presetstorage control feature
  • Direct Manual or preset recall control allows for an infinite selection ofdifferent lighting looks
  • Simple, powerful local preset storage and recall of 4 or 8 scenes withprogrammable fade times when used with an i Series e or i Series Quad dimmerrack
  • Virtually limitless DIMMER channel capacity
  • Multiple stations may be installed allowing control from several locations
  • Control stations can act independently of each other, together or as agroup
  • Take control feature
  • Selectable emergency power up mode feature - Preset 1 active or all offactive when power is applied to control station
  • Selectable multiple record mode lockout
  • Discrete digital control of 4 or 8 presets and/ or multiple overlappingsubmaster scenes
  • Direct integration capability with Remembrance Analog and Digital ControlStations and i Series e control electronics

Leviton RMB81-112 Specifications:


  • The control faceplate shall be constructed of formed steel painted white.
  • Silkscreen legends on faceplate shall be black. Preset and Manualselection buttons shall be black with green LED indicators. Off preset buttonshall contain a bi-colored LED for indicating various operating modes. Channelsliders shall have graduated silkscreen scales fitted with professional gradefader knobs.
  • The 4 slider with master control station and presets is 12" wide by 4-1/2"tall.  The station mounts in a NEMA 6 gang 3-1/2" deep back box. Contact the factory for recommended back box suppliers.
  • The 8 slider with master control station and presets is 15-5/8" wide by4-1/2" tall. The station mounts in a NEMA 8 gang 3-1/2" deep back box. Contactthe factory for recommended back box suppliers.


  • Push buttons. Control station shall contain 4 or 8 preset buttons with anintegral green LED, and a separate OFF button with an integral bi-colored LED.Manual push button shall be distinctively different to distinguish betweenmanual and preset modes. Control Stations can be wired to act independently ofeach other, or together as a group.
  • Slide Controllers. Control stations shall contain 4 or 8 slider channelswith a master. All potentiometers shall have at least a 2” travel and shall becapable of providing live, instantaneous control of the associated dimmers.The channel fader shall have the capacity of operating as an overlappingsubmaster for all dimmers within the control system. Channel sliders must beconfigured by a DMX512 control source.
  • Wiring. The control station requires power from a 10VAC @ 5V Atransformer. The control station requires a DMX512 control signal into thestation. The 4 preset control station wiring requires an Alpha 1898/8 orequivalent and a Belden 9829 or equivalent connected between the i Series e ori Series Quad dimmer racks and the control station. The 8 preset controlstation wiring requires an Alpha 1898/12 or equivalent and a Belden 9829 orequivalent connected between the i Series e or the i Series Quad dimmer racksand the control station.


  • Recall. The Control Station shall have the ability to activate a timedpreset, manually mix a scene, or enable both simultaneously at the press of asingle button. The corresponding LED on the button will illuminate.
  • Slider Record. Sliders shall be configured by capturing the DMX512 controlsignal into the unit. When enabled, the capture sequence is activated bypressing and holding the manual button in the ON mode with all sliders downfor at least five seconds, then sliding up the master and channel slider upwhere the scene is to be stored. The manual button must be pressed throughoutthe record sequence and held for an additional 3 seconds after the slidershave been raised. Slider record mode may be de-activated independently of thepreset record mode. When active, slider scenes pile onto or generate a DMX512signal. Slider scenes are stored in non-volatile memory.
  • Preset Record. When connected to an i Series e or i Series Quad, thecontrol station shall have the ability to store active DMX scene simply bypressing and holding the OFF button until the active scene lighting levels dipby 50%, and then while still holding the OFF button, pressing the presetbutton where the scene is to be stored. Preset record may be de-activatedindependently of slider record mode. Presets shall be stored in non-volatilememory.
  • Capacity. The control station shall have the ability to control avirtually limitless number of dimmer channels when used in conjunction with iSeries e or i Series Quad, or Remembrance Control Stations.
  • Record Lockout. The control station can be configured to disable sliderrecord mode, preset record mode, or both simultaneously.
  • Power Up State. The control station can be configured to active Preset 1on power up, or activate OFF on power up.
Add to Cart

We're sorry, only of this item available

Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM