RDL STVP2
ST-VP2

OUR PART #  STVP2


NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product. Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

Radio Design Labs' ST-VP2 can be wired into any line-level input of a paging amplifier. A line-level music source may be provided from a receiver, satellite decoder, tape or CD source. A line-level voice source may be provided from a telephone paging system at line level, or from a microphone which has been preamplified up to line level (See RDL STM-1, STM-2, STM-2X, STM-3 Microphone Preamplifiers). When a page is initiated, the module automatically senses the audio at the input, turns the music down to the desired level, and automatically fades the music back up after the page is completed. The VOICE input is completely turned off by the module until the next paging signal is received. Setup is made easy by two LED indicators at the front of the module. LEDs are provided to show correct operating level for each of the two inputs.

The music input provides an AGC / Compressor which transparently produces a consistent audio level for varying music sources and protects against excessive music levels which would otherwise mask the voice signal during voice-overs.

RDL ST-VP2 Specifications:

  • Inputs (2): Balanced line level (or unbalanced)
  • Input Impedance: 20 kO
  • Input Signal Range: -20 dBu to +18 dBu
  • Output: 0 dBu balanced (into 600 O)
  • Gain: Adjustable using multiturn potentiometer
  • THD+N: < 0.02% (20 Hz to 20 kHz, no compression)
  • Frequency Response: 25 Hz to 20 kHz (± 1 dB)
  • Noise: < -70 dB
  • Indicators (2): 1 LED indicating proper music level 1 LED indicating proper voice level
  • AGC/Compressor: 18 dB range; 6 dB compression at normal input level
  • Attack Time: 25 ms
  • Release Time: 2.5 seconds
  • Voice Trigger Level: 24 dB below operating level
  • Music Fade Depth: Adjustable 0 dB to -25 dB, or off
  • Music Recovery Delay: Adjustable 2 seconds to 4 seconds
  • Ambient Operating Environment: 0°C to 55°C
  • Power Requirement: GROUND-REFERENCED, 24 Vdc @ 35 mA
  • Package Type: Cardboard Box
  • Package Dimensions: 2" x 2" x 4"
  • Shipping Weight: 0.2 lbs.
  • WEEE weight: 0.145 lbs.
  • Tariff code: 8518.40.2000

WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov.

RDL STR19A STR-19A

RDL STR19A STR-19A

Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Log In For Price
In Stock
RDL PS24AS PS-24AS

RDL PS24AS PS-24AS

Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Log In For Price
In Stock
RDL STRRB1 ST-RRB1

RDL STRRB1 ST-RRB1

Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.
Log In For Price
In Stock
RDL DRA-35S  Din Rail Adaptor for STICK-ON

RDL DRA-35S Din Rail Adaptor for STICK-ON

The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Log In For Price
In Stock
RDL MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module

RDL MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module

Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Log In For Price
In Stock
RDL STR19B STR-19B

RDL STR19B STR-19B

Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...
Log In For Price
Please call for availability.
RDL SR4 SR-4

RDL SR4 SR-4

Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...
Log In For Price
Available to Order! Item usually SHIPS in 6-10 business days
RDL SR10 SR-10

RDL SR10 SR-10

Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
Log In For Price
Available to Order! Item usually SHIPS in 4 business days
RDL SR12A SR-12A

RDL SR12A SR-12A

Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.
Log In For Price
Available to Order! Item usually SHIPS in 6-10 business days
RDL SMK12 Smk 12 Mounting Strip for STICK-ON Units

RDL SMK12 Smk 12 Mounting Strip for STICK-ON Units

The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.
Log In For Price
Available to Order! Item usually SHIPS in 6-10 business days
RDL DTB-RDL Dtb Rdl Detachable Terminal Block

RDL DTB-RDL Dtb Rdl Detachable Terminal Block

Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.
Log In For Price
Available to Order! Item usually SHIPS in 4 business days

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM