Radio Design Labs D-AVMB2
Audio and Video Monitor BNC Panel

OUR PART #  D-AVMB2


RDL's D-AVMB2 is well-suited for installations requiring a wall-mounted audio and video monitor input or output plate for computers, monitors and projectors. The panel is typically installed as an audio/video input plate, but may equally be used as an output jack panel.

The front panel features a standard video monitor connector. Video components, video sync and their respective ground returns are separated to feed five BNC jacks on the rear panel. The BNC jacks are isolated from the module chassis ground so the appropriate signal grounds pass through without adding a video ground loop at the panel.

The front panel also features a single stereo mini-jack, intended for stereo consumer line-level audio sources. The left and right signal inputs are fed to a rear-panel detachable terminal block. The audio signals are unbalanced and are intended for short wiring runs where balanced lines are not required.

RDL D-AVMB2 BNC Panel Features:

  • Stereo audio input to stereo audio output
  • Stereo input on mini-jack
  • Unbalanced audio output on detachable terminal block
  • Video monitor input on standard video connector
  • Rear-panel video outputs (R,G,B,H,V) on BNC jacks
  • BNC jacks are isolated from chassis ground

RDL D-AVMB2 BNC Panel Specifications:

  • Audio input connector: Mini-jack 3.5 mm (Stereo)
  • Video input connector: Female DB15
  • Audio output connector: Detachable terminal block (Left and Right unbalanced audio)
  • Video output connectors (5): BNC (R: Red; G: Green; B: Blue; H: Horizontal Sync; V: Vertical Sync)
  • Dimensions: 4.13" H x 1.7" W x 1.4" D (10.49 x 4.32 x 3.56 cm) 
  • Mounting Box Minimum Dimensions:
    • Width: 1.8" (4.57 cm)
    • Depth: 0.15" (0.38 cm) plus the depth of the installer-provided BNC connectors
  • Shipping Weight: 0.39 lb
3RU Rack Panel Mount for 9 Decora Models
Radio Design Labs RM-D9 3RU Rack Panel Mount for 9 Decora Models
Radio Design Labs' RM-D9 is a 3 RU rack panel that allows the mounting of 9 Decora products, such as RDL remote controls and D-Series connector plates. The installer can label each installed module behind an included protection lens.The ...
Single-Gang Universal Wall Box
Radio Design Labs WB-1U Single-Gang Universal Wall Box
Can be mounted in International or US walls and cabinets. Features side and rear mounting holes which secure the box in new construction. Also has folding tabs which secure the box in an existing wall or cabinet.Dimensions: Height: 4.125 ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Wall Plate, Single Cover Plate, White
Radio Design Labs CP1-W Wall Plate, Single Cover Plate, White
For use with RDL R style remote controls and D style connector plates; Mount with RDL WB-1U Universal Wall Box.
Single-Gang Gray Wall Plate for SMB-1, DC-1, WB-1U, Decora-Style Products
Radio Design Labs CP-1/G Single-Gang Gray Wall Plate for SMB-1, DC-1, WB-1U, Decora-Style Products
Radio Design Labs' CP-1G is for use with RDL SMB-1, DC-1 and WB-1U for mounting RDL remote controls and jack panels.  Compatible with Decora style products and American electrical boxes.Height: 4.55" (11.6 cm)Width: 2.80" (7.1 cm)

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop or Wall-Mounting Decora Remote Control or Panel Chassis (Gray)
Radio Design Labs DC-4G Desktop or Wall-Mounting Decora Remote Control or Panel Chassis (Gray)
Radio Design Labs' DC-4G desktop chassis holds four Decora®-style products, including RDL remote controls and connector plates.  Installation is facilitated using the included mounting plate, which allows the chassis to mount to ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Wall Mount Chasis for Decora
Radio Design Labs DC-2G Wall Mount Chasis for Decora
The DC-2G desktop chassis holds two Decora®-style products, including RDL remote controls and connector plates. Installation is facilitated using the included mounting plate, which allows the chassis to mount to a tabletop or on a ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desk Top Chassis for Decora, White
Radio Design Labs DC-2W Desk Top Chassis for Decora, White
The DC-2W white desktop chassis holds two Decora®-style products, including RDL remote controls and connector plates. Installation is facilitated using the included mounting plate, which allows the chassis to mount to a tabletop or on a ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
1RU Rack Panel Mount for 3 Decora Models
Radio Design Labs RM-D3 1RU Rack Panel Mount for 3 Decora Models
Radio Design Labs' RM-D3 is a 1 RU rack panel that allows the mounting of 3 Decora products, such as RDL® remote controls and D-Series connector plates. The installer can label each installed module behind an included protection lens. The ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual-Gang Universal Wall Box
Radio Design Labs WB-2U Dual-Gang Universal Wall Box
Can be mounted in International or US walls and cabinets. Features side and rear mounting holes which secure the box in new construction. Also has folding tabs which secure the box in an existing wall or cabinet.Dimensions: Height: 4.125 ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Double Cover Plate/Gray
Radio Design Labs CP-2/G Double Cover Plate/Gray
For use with RDL R style remote controls and D style connector plates; Mount with RDL WB-2U Universal Wall Box. 

Usually ships in 7-14 business days.
Need it sooner? Call us!
Single Gang Decora Cover Plate in Stainless Steel
Radio Design Labs CP-1S Single Gang Decora Cover Plate in Stainless Steel
The Radio Design Labs CP-1S is a single gang decora cover plate in stainless steel.Dimensions: 4.55" H x 2.8" W (11.6 x 7.1 cm)Package Dimensions: 2" x 3"Shipping Weight: 0.072 lbs

Usually ships in 7-14 business days.
Need it sooner? Call us!

Radio Design Labs D-AVMB2
Audio and Video Monitor BNC Panel

OUR PART #  D-AVMB2

Product Information:

RDL's D-AVMB2 is well-suited for installations requiring a wall-mounted audio and video monitor input or output plate for computers, monitors and projectors. The panel is typically installed as an audio/video input plate, but may equally be used as an output jack panel.

The front panel features a standard video monitor connector. Video components, video sync and their respective ground returns are separated to feed five BNC jacks on the rear panel. The BNC jacks are isolated from the module chassis ground so the appropriate signal grounds pass through without adding a video ground loop at the panel.

The front panel also features a single stereo mini-jack, intended for stereo consumer line-level audio sources. The left and right signal inputs are fed to a rear-panel detachable terminal block. The audio signals are unbalanced and are intended for short wiring runs where balanced lines are not required.

RDL D-AVMB2 BNC Panel Features:

  • Stereo audio input to stereo audio output
  • Stereo input on mini-jack
  • Unbalanced audio output on detachable terminal block
  • Video monitor input on standard video connector
  • Rear-panel video outputs (R,G,B,H,V) on BNC jacks
  • BNC jacks are isolated from chassis ground

RDL D-AVMB2 BNC Panel Specifications:

  • Audio input connector: Mini-jack 3.5 mm (Stereo)
  • Video input connector: Female DB15
  • Audio output connector: Detachable terminal block (Left and Right unbalanced audio)
  • Video output connectors (5): BNC (R: Red; G: Green; B: Blue; H: Horizontal Sync; V: Vertical Sync)
  • Dimensions: 4.13" H x 1.7" W x 1.4" D (10.49 x 4.32 x 3.56 cm) 
  • Mounting Box Minimum Dimensions:
    • Width: 1.8" (4.57 cm)
    • Depth: 0.15" (0.38 cm) plus the depth of the installer-provided BNC connectors
  • Shipping Weight: 0.39 lb
3RU Rack Panel Mount for 9 Decora Models
Radio Design Labs RM-D9 3RU Rack Panel Mount for 9 Decora Models
Radio Design Labs' RM-D9 is a 3 RU rack panel that allows the mounting of 9 Decora products, such as RDL remote controls and D-Series connector plates. The installer can label each installed module behind an included protection lens.The ...
Single-Gang Universal Wall Box
Radio Design Labs WB-1U Single-Gang Universal Wall Box
Can be mounted in International or US walls and cabinets. Features side and rear mounting holes which secure the box in new construction. Also has folding tabs which secure the box in an existing wall or cabinet.Dimensions: Height: 4.125 ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Wall Plate, Single Cover Plate, White
Radio Design Labs CP1-W Wall Plate, Single Cover Plate, White
For use with RDL R style remote controls and D style connector plates; Mount with RDL WB-1U Universal Wall Box.
Single-Gang Gray Wall Plate for SMB-1, DC-1, WB-1U, Decora-Style Products
Radio Design Labs CP-1/G Single-Gang Gray Wall Plate for SMB-1, DC-1, WB-1U, Decora-Style Products
Radio Design Labs' CP-1G is for use with RDL SMB-1, DC-1 and WB-1U for mounting RDL remote controls and jack panels.  Compatible with Decora style products and American electrical boxes.Height: 4.55" (11.6 cm)Width: 2.80" (7.1 cm)

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop or Wall-Mounting Decora Remote Control or Panel Chassis (Gray)
Radio Design Labs DC-4G Desktop or Wall-Mounting Decora Remote Control or Panel Chassis (Gray)
Radio Design Labs' DC-4G desktop chassis holds four Decora®-style products, including RDL remote controls and connector plates.  Installation is facilitated using the included mounting plate, which allows the chassis to mount to ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Wall Mount Chasis for Decora
Radio Design Labs DC-2G Wall Mount Chasis for Decora
The DC-2G desktop chassis holds two Decora®-style products, including RDL remote controls and connector plates. Installation is facilitated using the included mounting plate, which allows the chassis to mount to a tabletop or on a ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desk Top Chassis for Decora, White
Radio Design Labs DC-2W Desk Top Chassis for Decora, White
The DC-2W white desktop chassis holds two Decora®-style products, including RDL remote controls and connector plates. Installation is facilitated using the included mounting plate, which allows the chassis to mount to a tabletop or on a ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
1RU Rack Panel Mount for 3 Decora Models
Radio Design Labs RM-D3 1RU Rack Panel Mount for 3 Decora Models
Radio Design Labs' RM-D3 is a 1 RU rack panel that allows the mounting of 3 Decora products, such as RDL® remote controls and D-Series connector plates. The installer can label each installed module behind an included protection lens. The ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual-Gang Universal Wall Box
Radio Design Labs WB-2U Dual-Gang Universal Wall Box
Can be mounted in International or US walls and cabinets. Features side and rear mounting holes which secure the box in new construction. Also has folding tabs which secure the box in an existing wall or cabinet.Dimensions: Height: 4.125 ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Double Cover Plate/Gray
Radio Design Labs CP-2/G Double Cover Plate/Gray
For use with RDL R style remote controls and D style connector plates; Mount with RDL WB-2U Universal Wall Box. 

Usually ships in 7-14 business days.
Need it sooner? Call us!
Single Gang Decora Cover Plate in Stainless Steel
Radio Design Labs CP-1S Single Gang Decora Cover Plate in Stainless Steel
The Radio Design Labs CP-1S is a single gang decora cover plate in stainless steel.Dimensions: 4.55" H x 2.8" W (11.6 x 7.1 cm)Package Dimensions: 2" x 3"Shipping Weight: 0.072 lbs

Usually ships in 7-14 business days.
Need it sooner? Call us!
Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM