Lowell LPTR4-2123
21 RU Pull & Turn Rack

OUR PART #  LPTR4-2123


Lowell's Pull & Turn Rack for built-in wall and millwork applications features a turntable on four, heavy-duty slides for smooth pullout access to rackmounted equipment. Load capacity is 300 lbs. Sturdy system is engineered for efficient on-site installation and packaged unassembled in two cartons so that the bottom base (with slides and integral turntable) along with two rear corner post rails and three cable lacing bars can be sent ahead to the job site and installed in a boxed wall opening or cabinet. The second carton contains the rack base, front and rear posts, side stiffeners, front vent panel and three lacing bars to assemble the rack for pre-loading and testing of equipment in the shop - a real benefit for corporate boardroom and training facility installations.

The bottom base installs using (8) screws and may be mounted flush or recessed up to 2” into a boxed wall or cabinetry to allow for equipment protrusions. The removable rack base, with or without mounted equipment, easily docks and secures to the bottom base using two screws on the front and rear frame (no wing nuts under the rack). When all equipment is in place and wired, the assembly is secured in fixed position with two screws through a perforated front security panel. To facilitate wiring and servicing of rack equipment, the security panel may be removed; allowing the rack to be pulled out smoothly from the wall or millwork on the heavy-duty slides. A convenient pushbutton lock and release, accessible in the center front of the bottom base, allows the rack to rotate 60º and 90º on the turntable. Note the rack must be fully forward to rotate with adequate clearance. If it is recessed up to 2” it will not rotate the full 900. When servicing is complete, use the pushbutton to return the rack to its front-facing position, push it back into the wall and re-install the front security panel. Components are manufactured from certified US steel and finished in smooth black powder epoxy. Choose models with panel space of 10, 12, 16 or 21RU. All provide 23” useable depth (23.22” overall).

Features:

  • Bottom base with turntable and 4 heavy-duty slides for 300 lb. load
  • Removable rack base
  • 6 corner-post rails (10-32) and 2-side stiffeners
  • Cable lacing panels (6)
  • Front security panel, perforated
  • Black powder epoxy finish

Specifications:

  • Rack Units:  21
  • Panel Space:  36.75"
  • Overall Height:  39.33"
  • Overall Width:  19.13"
  • Overall Depth:  23.23"
  • Useable Depth:  23.00"
  • Load Capacity:  300 lbs
  • Cable Tie-off Panels:  6

Lowell LPTR4-2123
21 RU Pull & Turn Rack

OUR PART #  LPTR4-2123

Product Information:

Lowell's Pull & Turn Rack for built-in wall and millwork applications features a turntable on four, heavy-duty slides for smooth pullout access to rackmounted equipment. Load capacity is 300 lbs. Sturdy system is engineered for efficient on-site installation and packaged unassembled in two cartons so that the bottom base (with slides and integral turntable) along with two rear corner post rails and three cable lacing bars can be sent ahead to the job site and installed in a boxed wall opening or cabinet. The second carton contains the rack base, front and rear posts, side stiffeners, front vent panel and three lacing bars to assemble the rack for pre-loading and testing of equipment in the shop - a real benefit for corporate boardroom and training facility installations.

The bottom base installs using (8) screws and may be mounted flush or recessed up to 2” into a boxed wall or cabinetry to allow for equipment protrusions. The removable rack base, with or without mounted equipment, easily docks and secures to the bottom base using two screws on the front and rear frame (no wing nuts under the rack). When all equipment is in place and wired, the assembly is secured in fixed position with two screws through a perforated front security panel. To facilitate wiring and servicing of rack equipment, the security panel may be removed; allowing the rack to be pulled out smoothly from the wall or millwork on the heavy-duty slides. A convenient pushbutton lock and release, accessible in the center front of the bottom base, allows the rack to rotate 60º and 90º on the turntable. Note the rack must be fully forward to rotate with adequate clearance. If it is recessed up to 2” it will not rotate the full 900. When servicing is complete, use the pushbutton to return the rack to its front-facing position, push it back into the wall and re-install the front security panel. Components are manufactured from certified US steel and finished in smooth black powder epoxy. Choose models with panel space of 10, 12, 16 or 21RU. All provide 23” useable depth (23.22” overall).

Features:

  • Bottom base with turntable and 4 heavy-duty slides for 300 lb. load
  • Removable rack base
  • 6 corner-post rails (10-32) and 2-side stiffeners
  • Cable lacing panels (6)
  • Front security panel, perforated
  • Black powder epoxy finish

Specifications:

  • Rack Units:  21
  • Panel Space:  36.75"
  • Overall Height:  39.33"
  • Overall Width:  19.13"
  • Overall Depth:  23.23"
  • Useable Depth:  23.00"
  • Load Capacity:  300 lbs
  • Cable Tie-off Panels:  6
Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM