Radio Design Labs EZ-MPA1
Mic Preamp with Compressor, Stereo Output

OUR PART #  EZ-MPA1


The EZ-MPA1 is a microphone preamplifier with front-panel volume control and audio level metering. A front-panel switch engages an audio compressor to control overloads and clipping during high level audio bursts or peaks from the microphone. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The preamplified mic signal feeds both channels of the line output on RCA or MINI jacks. LED VU metering facilitates easy level adjustment.

The EZ-MPA1 is ideal for adding microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems. Power supply included.

Features:

  • Balanced Microphone Input on Rear-Panel XLR
  • Switch-Selectable Phantom on Rear Panel
  • Unbalanced Output on MINI or RCA Rear-Panel Jacks
  • Preamp Feeds Left and Right Output Channels
  • Front-Panel Compressor Enable/Disable Switch
  • Audio Compressor Controls Overloads
  • Front-Panel LEVEL Control
  • Dual-LED VU Meter

Specifications:

  • Input: 1.2 kO balanced on XLR jack, mic-level, -11 dBu max.
  • Level control: Off to 50 dB gain
  • Outputs (2): -10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
  • Frequency Response: 80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
  • THD+N: < 0.1% (35 Hz to 20 kHz, -50 dBu input)
  • Compression: 20 dB range, switch-selectable
  • CMRR: > 55 dB (20 to 20 kHz)
  • Metering: Dual-LED VU Meter, calibrated to -10 dBV output
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -65 dB (below -10 dBV output, -50 dBu input)
  • 24 Vdc power supply current: 55 mA (idle), 80 mA (max.), 100 mA (max. with phantom) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75" (14.6 cm)W x 3" (7.6 cm)D
  • Mounting size: 1/3 rack width
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
The Radio Design Labs EZ-UCB2 is a under counter bracket pair for all EZ product widths. Radio Design Labs EZ-UCB2 Features: Brackets Snap on EZ Case for Easy Alignment EZ Product Secures Quickly Using Two Screws Brackets Fasten to ...
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet

Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire

Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs EZ-MPA1
Mic Preamp with Compressor, Stereo Output

OUR PART #  EZ-MPA1

Product Information:

The EZ-MPA1 is a microphone preamplifier with front-panel volume control and audio level metering. A front-panel switch engages an audio compressor to control overloads and clipping during high level audio bursts or peaks from the microphone. Dynamic or condenser microphones are both supported with rear-panel switchable phantom voltage. The preamplified mic signal feeds both channels of the line output on RCA or MINI jacks. LED VU metering facilitates easy level adjustment.

The EZ-MPA1 is ideal for adding microphone inputs to mixers and amplifiers with line inputs. It is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms, studios and commercial sound systems. Power supply included.

Features:

  • Balanced Microphone Input on Rear-Panel XLR
  • Switch-Selectable Phantom on Rear Panel
  • Unbalanced Output on MINI or RCA Rear-Panel Jacks
  • Preamp Feeds Left and Right Output Channels
  • Front-Panel Compressor Enable/Disable Switch
  • Audio Compressor Controls Overloads
  • Front-Panel LEVEL Control
  • Dual-LED VU Meter

Specifications:

  • Input: 1.2 kO balanced on XLR jack, mic-level, -11 dBu max.
  • Level control: Off to 50 dB gain
  • Outputs (2): -10 dBV nominal on RCA jacks or Mini jack, +16 dBV max. without compression, -4 dBV max. with 20 dB compression
  • Frequency Response: 80 Hz to 40 kHz (±1 dB, mic input, -6 dB at 20 Hz with integral high-pass filter)
  • THD+N: < 0.1% (35 Hz to 20 kHz, -50 dBu input)
  • Compression: 20 dB range, switch-selectable
  • CMRR: > 55 dB (20 to 20 kHz)
  • Metering: Dual-LED VU Meter, calibrated to -10 dBV output
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -65 dB (below -10 dBV output, -50 dBu input)
  • 24 Vdc power supply current: 55 mA (idle), 80 mA (max.), 100 mA (max. with phantom) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75" (14.6 cm)W x 3" (7.6 cm)D
  • Mounting size: 1/3 rack width
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
The Radio Design Labs EZ-UCB2 is a under counter bracket pair for all EZ product widths. Radio Design Labs EZ-UCB2 Features: Brackets Snap on EZ Case for Easy Alignment EZ Product Secures Quickly Using Two Screws Brackets Fasten to ...
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet

Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire

Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM