Radio Design Labs EZ-PA20
10W RMS/Channel @ 8 Ohms Stereo Amplifier

OUR PART #  EZ-PA20

Log In for price!

Don't have an account? Apply today!

Radio Design Labs' EZ-PA20 is a stereo audio amplifier with one line input and a front-panel volume control. An integral compressor/limiter allows a higher sound output level without clipping than a standard amplifier. The outputs drive 4 or 8 ohm speakers.

The EZ-PA20 is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms and commercial sound systems. Power supply included.

Radio Design Labs EZ-PA20 Features:

  • Audio Amplifier with Front-Panel Level Control
  • 10 Watts RMS Per Channel into 8 Ohms
  • 8 Watts RMS Per Channel into 4 Ohms
  • Switch-Selectable Load Impedance on Rear Panel
  • Unbalanced Line Input on RCA Jacks
  • Switch-Selectable Mono or Stereo Mode
  • Integral Overload Limiter with LED Indicator
  • Limiter Controls Overloads from Clipping

Radio Design Labs EZ-PA20 Specifications:

  • Input: > 10 kOhm, -10 dBV nominal on RCA jacks, -13 dBV Min. (for 10 Wout), +22 dBV max.
  • Gain: Off to 32 dB
  • Outputs (2): Left and Right, 10 Watts RMS into 8 Ohms per channel or 8Watts RMS into 4 Ohms per channel, switch-selectable output impedance
  • Frequency Response: 35 Hz to 20 kHz (±1.5 dB, 10 Watts)
  • THD+N: < 0.25%
  • Crosstalk: < -68 dB (1 kHz)
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -70 dB (below 10 Watts)
  • 24 Vdc power supply current: 160 mA (idle), 1000 mA (max.) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75" W x 5" D (14.6 x 12.7 cm)
  • Mounting size: 1/3 rack width
24V @ 1000mA Power Supply
Radio Design Labs PS24KS 24V @ 1000mA Power Supply
Typical Performance: Input: 100 to 240 VAC Output: 24 Vdc, 1 A (UL, CSA) Dimensions: 1.80" x 3.51" x 1.55" (4.6  x 8.9 x 3.9 cm) Efficiency: ENERGY STAR Level IV
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
The Radio Design Labs EZ-UCB2 is a under counter bracket pair for all EZ product widths. Radio Design Labs EZ-UCB2 Features: Brackets Snap on EZ Case for Easy Alignment EZ Product Secures Quickly Using Two Screws Brackets Fasten to ...
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet
Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack
Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs EZ-PA20
10W RMS/Channel @ 8 Ohms Stereo Amplifier

OUR PART #  EZ-PA20

Product Information:

Radio Design Labs' EZ-PA20 is a stereo audio amplifier with one line input and a front-panel volume control. An integral compressor/limiter allows a higher sound output level without clipping than a standard amplifier. The outputs drive 4 or 8 ohm speakers.

The EZ-PA20 is used in houses of worship, restaurants, clubs, meeting rooms, educational facilities, conference rooms and commercial sound systems. Power supply included.

Radio Design Labs EZ-PA20 Features:

  • Audio Amplifier with Front-Panel Level Control
  • 10 Watts RMS Per Channel into 8 Ohms
  • 8 Watts RMS Per Channel into 4 Ohms
  • Switch-Selectable Load Impedance on Rear Panel
  • Unbalanced Line Input on RCA Jacks
  • Switch-Selectable Mono or Stereo Mode
  • Integral Overload Limiter with LED Indicator
  • Limiter Controls Overloads from Clipping

Radio Design Labs EZ-PA20 Specifications:

  • Input: > 10 kOhm, -10 dBV nominal on RCA jacks, -13 dBV Min. (for 10 Wout), +22 dBV max.
  • Gain: Off to 32 dB
  • Outputs (2): Left and Right, 10 Watts RMS into 8 Ohms per channel or 8Watts RMS into 4 Ohms per channel, switch-selectable output impedance
  • Frequency Response: 35 Hz to 20 kHz (±1.5 dB, 10 Watts)
  • THD+N: < 0.25%
  • Crosstalk: < -68 dB (1 kHz)
  • Phantom: Switch-selectable 24 V (IEC 1938: 1996-12)
  • Noise: < -70 dB (below 10 Watts)
  • 24 Vdc power supply current: 160 mA (idle), 1000 mA (max.) Power supply included.
  • Power supply input voltage: 100 to 240 VAC
  • Warranty: 3 Years; contact RDL technical support department for assistance
  • Case dimensions: 5.75" W x 5" D (14.6 x 12.7 cm)
  • Mounting size: 1/3 rack width
24V @ 1000mA Power Supply
Radio Design Labs PS24KS 24V @ 1000mA Power Supply
Typical Performance: Input: 100 to 240 VAC Output: 24 Vdc, 1 A (UL, CSA) Dimensions: 1.80" x 3.51" x 1.55" (4.6  x 8.9 x 3.9 cm) Efficiency: ENERGY STAR Level IV
Surface Mount Bezel 1/3 Rack
Radio Design Labs EZ-SMB2 Surface Mount Bezel 1/3 Rack
Surface mount bezel for 1/3 rack width EZ products.
Under Counter Bracket
Radio Design Labs EZ-UCB2 Under Counter Bracket
The Radio Design Labs EZ-UCB2 is a under counter bracket pair for all EZ product widths. Radio Design Labs EZ-UCB2 Features: Brackets Snap on EZ Case for Easy Alignment EZ Product Secures Quickly Using Two Screws Brackets Fasten to ...
Component Chasis, 6 x 1/6 RU
Radio Design Labs EZ-CC6 Component Chasis, 6 x 1/6 RU
Component Chassis for 6 Increments of 1/6 Rack WidthFeatures: Mounts All EZ A/V Products Mounts EZ Storage Drawers Cover Lifts Off for Easy Product Mounting Integral Heavy-Duty Non-Skid Rubber Feet
Usually ships in 7-14 business days.
Need it sooner? Call us!
Rack Adapter
Radio Design Labs EZ-RA6 Rack Adapter
Rack Adapter for 6 Increments of 1/6 Rack Width Mounts All EZ A/V Products Mounts EZ Storage Drawers Base Plate Slides Out for Easy Product Mounting Occupies One RU in Standard 19¨ Rack
Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Chassis 1/3 Rack
Radio Design Labs EZ-DC2 Desktop Chassis 1/3 Rack
Desktop Chassis for 1/3 Rack Width EZ Products Mounts 1/3 Width EZ Product to Desktop Installs Quickly With Two Screws Covers Cable Port in Desktop Provides Space for Excess Wire
Usually ships in 7-14 business days.
Need it sooner? Call us!
1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
Radio Design Labs EZ-SD1 1/6 Rack Width Storage Drawer for EZ-RA6 or EZ-CC6
RDL's EZ-SD1 is a 1/6 rack width storage drawer designed to mount in RDL's EZ-CC6 or EZ-RA6 rack adapters. The drawer holds adapters and cables and can be used in place of filler panels.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Filler Panel, 1/6RU
Radio Design Labs EZ-FP1 Filler Panel, 1/6RU
Filler Panel - 1/6 Rack Width for EZ-RA6 or EZ-CC6.
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

HACKER SAFE certified sites prevent over 99.9% of hacker crime.