Ashly ne8250.70pe
8 Channel 70V Power Amplifier with DSP

OUR PART #  NE8250.70PE


Connecting and controlling an amplifier for networked systems has now been simplified with Ashly’s NE Series amplifiers. Network Enabled (NE) amplifiers offer ease of use, setup and control using standard 10/100 Ethernet protocol and Protea NE Software. No special outboard control units are needed.

Eight, eight-channel models with output power at 250W are available to fill a wide variety of low impedance, 25V, 70V and 100V performance installation or constant voltage applications. NE Series amplifiers are offered two ways; standard input with euroblock connectors and “pe” (Protea Enabled) with euroblock input connectors and world renowned Protea DSP signal processing.

The DSP signal processing library is extensive and utilizes two SHARC 32-bit/ 96kHz processors. Processing blocks include Graphic, Parametric, Notch and Shelving Equalization, High-, Low- and All-Pass Filters (HPF/LPF/APF) with up to 48dB/Octave slopes, Delay, Compressor/Limiter, Gate, Ducking, Auto-leveler, Gain and Signal Generators (sinewave, white and pink noise). A full Matrix Mixer with assignable routing allows any input to drive any or all amplifier outputs. Presets can be used to store and retrieve global parameters of an entire amplifier’s control surface and DSP section.

Additionally, each amplifier also provides DC voltage control of the attenuators which makes it a snap to control volume from remote locations, preset recall, Remote Power Standby and data in and out ports for connecting accessories like the WR-5 to control user selected parameters. There are LED indicators for power, standby, protect, network communications and each channel has a four-step signal meter, bridge mono, temperature and current indicators.

Four-channel Mic-pre, AES/EBU, EtherSound, and Cobranet modules will be available as options. Four-channel NE series amplifiers are also available.

Ashly ne8250.70pe Features:

  • Ethernet control Is standard
  • Low-Z, 25V, 70V and 100V Models
  • Extensive DSP Available
  • Easy and intuitive user interface
  • Extensive protection circuitry
  • Safety/Compliance: CE, FCC, RoHS
  • Optional CobraNet, EtherSound, AES/EBU, Mic Preamps
  • Front panel:
    • Level attenuators for each channel
    • Power switch can be disabled by software
    • 4-Step Signal Level and Clip LEDs
  • Rear panel:
    • 10/100 Ethernet port
    • Euroblock inputs
    • Euroblock outputs
    • Remote level control
    • Preset recall
    • Remote power standby
    • Data in and out ports

Ashly ne8250.70pe Specifications:

  • Rated Power 25V, 70V, 100V (per channel): 250W
  • S/N (20 Hz-20 kHz, unweighted): >105dB
  • 1/8th Output (Pink Noise): 31.25W
  • 1/8th Draw (Pink Noise): 360W
  • 1/8th Current (Pink Noise): 4.8A
  • Idle Power: 35W
  • Idle Current: 0.5A
  • Weight: Net Shipping: 26lbs.
  • Frequency Response (8 ohms): 20 Hz - 20k Hz,(unweighted) ±1dB
  • Input Impedance: 20k ohms, balanced
  • Input Sensitivity: 6.2dBu
  • Maximum Input Level: +21dBu
  • Internal HPF ( 25V, 70V, 100V models) (contolled bysoftware):
    • 80Hz (12dB/oct)
    • 400Hz (6dB/oct)
    • OFF
  • Damping Factor (8 ohms): > 250
  • Cooling: Temperature dependent speed-controlled fan (Front in, Side out)
  • Output Circuitry: Class D
  • Connectors (each channel):
    • Input - Euroblock
    • Output - Euroblock
  • Front Controls:
    • AC Power Switch
    • Individual input attenuators
  • Front indicators (LED color):
    • Power (Blue)
    • Standby (Yellow)
    • Protect (Red)
    • Disable (Yellow)
    • Com (Green)
    • Bridge (Green)
    • Signal Level -18dB,-12dB (Green), -6dB (Yellow), Clip (Red)
    • Temp (Yellow)
  • Rear Controls:
    • Ethernet 10/100
    • Channel bridge switch (Low-Z only)
    • Remote standby
    • Preset recall (4)
    • Remote Level (8)
  • Remote Data:
    • Amplifier and Load Protection Output Overcurrent
    • Main Supply Rail Overvoltage
    • Chassis Temperature
    • Inrush Limiting
    • Mains Fuse
  • Cordset: 15A Edison 3-Prong IEC
  • Dimensions (HxWxD): 3.5" (2RU) x 19" x 15.5" (88.9 x483 x 394 mm)
  • Environmental: 40°-120°F (4°-49°C) non-condensing
8 channel Network Fader Remote Control
Ashly FR-8 8 channel Network Fader Remote Control
The Ashly FR-8 and FR-16 are Ethernet devices that provide fader-based remote level control for Ashly NE (network enabled) products having DSP capabilities. The FR-8 controls up to eight user assigned inputs, outputs, or mixer outputs, and ...
Programmable Zone Controller, Wall Mount, Six Button
Ashly WR-5 Programmable Zone Controller, Wall Mount, Six Button
The WR-5 is a microprocessor-based remote control unit for use with NE Series Amplifiers and processors and the Protea 24.24M. The WR-5 is designed to fit into a standard electrical wall box for remote control of assignable functions. ...
4-Positon Preset Recall Wallplate Remote for Ashly 24.24M
Ashly WR-2 4-Positon Preset Recall Wallplate Remote for Ashly 24.24M
The WR-2 allows selection of one of four presets via interlocking pushbutton switches. Each pushbutton switch connects to a screw-terminal on the rear of the 24.24M (labeled "1" through "8" "Preset Recall"). The terminal numbers correspond ...
Network Fader Remote Control, 16 Channel
Ashly FR-16 Network Fader Remote Control, 16 Channel
The Ashly FR-8 and FR-16 are Ethernet devices that provide fader-based remote level control for Ashly NE (network enabled) products having DSP capabilities. The FR-8 controls up to eight user assigned inputs, outputs, or mixer outputs, and ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
8-Channel Remote Level Control
Ashly RW8C 8-Channel Remote Level Control
The RD-8C and RW-8C are remote level controllers which can be used with the VCM-88C and Protea 24.24M. The RD-8C is a desktop controller, while the RW-8C is electronically the same but mounts as a wall plate using a standard 4-gang ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Remote
Ashly RD8C Desktop Remote
The RD-8C and RW-8C are remote level controllers which can be used with the VCM-88C and Protea 24.24M. The RD-8C is a desktop controller, while the RW-8C is electronically the same but mounts as a wall plate using a standard 4-gang ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Remote, 6-button Network
Ashly NEWR-5 Remote, 6-button Network
The neWR-5 is a programmable Ethernet based remote control unit for Ashly NE Series and Pêma products. Connecting and powering the neWR-5 is done using standard Cat-5 Ethernet cable and an IEEE 802.3af Power over Ethernet (PoE) switch or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
2 Control Level Wallplate Remote for Ashly 24.24M
Ashly WR-1 2 Control Level Wallplate Remote for Ashly 24.24M
The WR-1 is an assignable, dual potentiometer remote volume control for the 24.24M. Each volume control is connected to a euroblock jack terminal on the WR-1 circuit board, which in turn must be wired to the 24.24M back panel euroblock ...

Usually ships in 7-14 business days.
Need it sooner? Call us!

Ashly ne8250.70pe
8 Channel 70V Power Amplifier with DSP

OUR PART #  NE8250.70PE

Product Information:

Connecting and controlling an amplifier for networked systems has now been simplified with Ashly’s NE Series amplifiers. Network Enabled (NE) amplifiers offer ease of use, setup and control using standard 10/100 Ethernet protocol and Protea NE Software. No special outboard control units are needed.

Eight, eight-channel models with output power at 250W are available to fill a wide variety of low impedance, 25V, 70V and 100V performance installation or constant voltage applications. NE Series amplifiers are offered two ways; standard input with euroblock connectors and “pe” (Protea Enabled) with euroblock input connectors and world renowned Protea DSP signal processing.

The DSP signal processing library is extensive and utilizes two SHARC 32-bit/ 96kHz processors. Processing blocks include Graphic, Parametric, Notch and Shelving Equalization, High-, Low- and All-Pass Filters (HPF/LPF/APF) with up to 48dB/Octave slopes, Delay, Compressor/Limiter, Gate, Ducking, Auto-leveler, Gain and Signal Generators (sinewave, white and pink noise). A full Matrix Mixer with assignable routing allows any input to drive any or all amplifier outputs. Presets can be used to store and retrieve global parameters of an entire amplifier’s control surface and DSP section.

Additionally, each amplifier also provides DC voltage control of the attenuators which makes it a snap to control volume from remote locations, preset recall, Remote Power Standby and data in and out ports for connecting accessories like the WR-5 to control user selected parameters. There are LED indicators for power, standby, protect, network communications and each channel has a four-step signal meter, bridge mono, temperature and current indicators.

Four-channel Mic-pre, AES/EBU, EtherSound, and Cobranet modules will be available as options. Four-channel NE series amplifiers are also available.

Ashly ne8250.70pe Features:

  • Ethernet control Is standard
  • Low-Z, 25V, 70V and 100V Models
  • Extensive DSP Available
  • Easy and intuitive user interface
  • Extensive protection circuitry
  • Safety/Compliance: CE, FCC, RoHS
  • Optional CobraNet, EtherSound, AES/EBU, Mic Preamps
  • Front panel:
    • Level attenuators for each channel
    • Power switch can be disabled by software
    • 4-Step Signal Level and Clip LEDs
  • Rear panel:
    • 10/100 Ethernet port
    • Euroblock inputs
    • Euroblock outputs
    • Remote level control
    • Preset recall
    • Remote power standby
    • Data in and out ports

Ashly ne8250.70pe Specifications:

  • Rated Power 25V, 70V, 100V (per channel): 250W
  • S/N (20 Hz-20 kHz, unweighted): >105dB
  • 1/8th Output (Pink Noise): 31.25W
  • 1/8th Draw (Pink Noise): 360W
  • 1/8th Current (Pink Noise): 4.8A
  • Idle Power: 35W
  • Idle Current: 0.5A
  • Weight: Net Shipping: 26lbs.
  • Frequency Response (8 ohms): 20 Hz - 20k Hz,(unweighted) ±1dB
  • Input Impedance: 20k ohms, balanced
  • Input Sensitivity: 6.2dBu
  • Maximum Input Level: +21dBu
  • Internal HPF ( 25V, 70V, 100V models) (contolled bysoftware):
    • 80Hz (12dB/oct)
    • 400Hz (6dB/oct)
    • OFF
  • Damping Factor (8 ohms): > 250
  • Cooling: Temperature dependent speed-controlled fan (Front in, Side out)
  • Output Circuitry: Class D
  • Connectors (each channel):
    • Input - Euroblock
    • Output - Euroblock
  • Front Controls:
    • AC Power Switch
    • Individual input attenuators
  • Front indicators (LED color):
    • Power (Blue)
    • Standby (Yellow)
    • Protect (Red)
    • Disable (Yellow)
    • Com (Green)
    • Bridge (Green)
    • Signal Level -18dB,-12dB (Green), -6dB (Yellow), Clip (Red)
    • Temp (Yellow)
  • Rear Controls:
    • Ethernet 10/100
    • Channel bridge switch (Low-Z only)
    • Remote standby
    • Preset recall (4)
    • Remote Level (8)
  • Remote Data:
    • Amplifier and Load Protection Output Overcurrent
    • Main Supply Rail Overvoltage
    • Chassis Temperature
    • Inrush Limiting
    • Mains Fuse
  • Cordset: 15A Edison 3-Prong IEC
  • Dimensions (HxWxD): 3.5" (2RU) x 19" x 15.5" (88.9 x483 x 394 mm)
  • Environmental: 40°-120°F (4°-49°C) non-condensing
8 channel Network Fader Remote Control
Ashly FR-8 8 channel Network Fader Remote Control
The Ashly FR-8 and FR-16 are Ethernet devices that provide fader-based remote level control for Ashly NE (network enabled) products having DSP capabilities. The FR-8 controls up to eight user assigned inputs, outputs, or mixer outputs, and ...
Programmable Zone Controller, Wall Mount, Six Button
Ashly WR-5 Programmable Zone Controller, Wall Mount, Six Button
The WR-5 is a microprocessor-based remote control unit for use with NE Series Amplifiers and processors and the Protea 24.24M. The WR-5 is designed to fit into a standard electrical wall box for remote control of assignable functions. ...
4-Positon Preset Recall Wallplate Remote for Ashly 24.24M
Ashly WR-2 4-Positon Preset Recall Wallplate Remote for Ashly 24.24M
The WR-2 allows selection of one of four presets via interlocking pushbutton switches. Each pushbutton switch connects to a screw-terminal on the rear of the 24.24M (labeled "1" through "8" "Preset Recall"). The terminal numbers correspond ...
Network Fader Remote Control, 16 Channel
Ashly FR-16 Network Fader Remote Control, 16 Channel
The Ashly FR-8 and FR-16 are Ethernet devices that provide fader-based remote level control for Ashly NE (network enabled) products having DSP capabilities. The FR-8 controls up to eight user assigned inputs, outputs, or mixer outputs, and ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
8-Channel Remote Level Control
Ashly RW8C 8-Channel Remote Level Control
The RD-8C and RW-8C are remote level controllers which can be used with the VCM-88C and Protea 24.24M. The RD-8C is a desktop controller, while the RW-8C is electronically the same but mounts as a wall plate using a standard 4-gang ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Desktop Remote
Ashly RD8C Desktop Remote
The RD-8C and RW-8C are remote level controllers which can be used with the VCM-88C and Protea 24.24M. The RD-8C is a desktop controller, while the RW-8C is electronically the same but mounts as a wall plate using a standard 4-gang ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Remote, 6-button Network
Ashly NEWR-5 Remote, 6-button Network
The neWR-5 is a programmable Ethernet based remote control unit for Ashly NE Series and Pêma products. Connecting and powering the neWR-5 is done using standard Cat-5 Ethernet cable and an IEEE 802.3af Power over Ethernet (PoE) switch or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
2 Control Level Wallplate Remote for Ashly 24.24M
Ashly WR-1 2 Control Level Wallplate Remote for Ashly 24.24M
The WR-1 is an assignable, dual potentiometer remote volume control for the 24.24M. Each volume control is connected to a euroblock jack terminal on the WR-1 circuit board, which in turn must be wired to the 24.24M back panel euroblock ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM