Clear-Com TW12C
Encore CC/RTS System Interface

OUR PART #  TW12C


Clear-Com's TW-12C intercom system interface is designed for connecting one intercom system to another, without compromising the audio quality of either system.

Transparent Isolation Between Systems
The unique TW-12C completely eliminates hums and buzzes caused by ground loops. The TW-12C compensates not only for level differences between systems, but for varying impedances caused by transformers and capacitance on the lines.

The TW-12C provides an electrically isolated interface between the two intercom systems. Either "side" of the interface can connect to a Clear-Com intercom system or an RTS intercom system, allowing Clear-Com-to-Clear-Com, Clear-Com-to-RTS, and RTS-to-RTS combinations. In addition, the TW-12C passes through and translates "call" signals, Clear-Com-to-RTS and vice versa.

The interface consists of two identical, 2-wire-to-4-wire hybrid networks which break the ground loops that occur when two systems are run from separate power sources. The audio paths are transformer-coupled and the signaling circuits are opto-isolated.

Fast, Easy & Accurate Setup
The operator can quickly set up the TW-12C by using a standard intercom headset and the TW-12C's built-in setup tone. The TW-12C is capable of a range of null adjustments, allowing it to adapt to a wide variety of line conditions, line lengths, and impedances.

The TW-12C provides each side of the system with null adjustment controls that allow adjustment even when the system is operating. The rear panel of the TW-12C contains a pair of 3-pin XLR connectors (one male, one female) for each side of the interface.

Call Signal Translation
The TW-12C interface receives "Call" signaling in the appropriate form (DC level for Clear-Com, tone for RTS), decodes it, and passes it to the other side of the interface, via an optical coupler. The receiving side of the interface sends the signal appropriate for the connected intercom.

Power
Each side of the TW-12C is powered directly by the intercom system to which it is connected. The unit draws about the same amount of power as a belt-pack. If either system is disconnected, the power loss immediately shuts down the associated electronics, eliminating any unwanted noises on the operating intercom side. The TW-12C front panel provides an LED power indicator for each side of the interface.

Clear-Com TW12C Features:

  • Eliminates grounding problems between intercom systems
  • Matches gain between systems
  • Provides system isolation for: Clear-Com toClear-Com; Clear-Com to RTS; RTS to RTS
  • Passes through and translates signaling
  • Provides superior hybrid nulling - up to 40dB
  • Setup tone allows adjustment during operation
  • Powered from connected systems
  • Uses just one rack space

Clear Com Format

  • Line Characteristics
    • Max Level Before Clipping :>=3dBu
    • Impedance: >=10Kohms
    • < /UL>< LI>Signalling
      • Receive: <=4 VDC
      • Send: >=11VDC

    RTS Format

    • Line Characteristics
      • Max Level Before Clipping :>=5dBu
      • Impedance: >=10Kohms
      • < /UL>
      • SignallingTone
        • Send frequency: 20kHz ±100Hz
        • Receive frequency:20kHz ±500Hz
        • Send level: >=-6dBu
        • Receive level: <=-25dBu

      Clear-Com TW12C Specifications:

      • Frequency response
        • Party Line- Party Line: 200-8KHz
      • Distortion
        • Party Line - PartyLine: <=0.2%
        • < /UL>
        • Max Gain
          • ClearCom - RTS: >=9dB
          • ClearCom - ClearCom:>=4dB
          • RTS - ClearCom: >=-1dB
          • RTS -RTS: >=4dB
          • < /UL>
          • Min Gain
            • ClearCom - RTS: <=1dB
            • ClearCom - ClearCom:<=-4dB
            • RTS - ClearCom: <=-9dB
          • Power Requirements
            • Input Voltage Range: 20-30VDC
            • Input Current (average):<=50mA
            • < /UL>
            • Rear Panel Connectors
              • (2) XLR3M (1 per channel)
              • (2) XLR3F (1 per channel)
            • Front Panel Connectors
              • Headset: (1) XLR4M
              • TS1 Earphone:(1) 3.5mm Jack Socket
            • Front Panel Controls and Indicators
              • Power: (2) Green LED (1 perchannel)
              • Null Test Button : (2) Buttons (1 per channel)
              • Gain LevelAdjust: (2) Controls (1 per channel)
              • Null Adjust: (6) Controls (3 perchannel)
              • Connection Type Switch: (2) Switches (1 per channel)
              • Pin Connection Select Switch: (2) Switches (1 per channel)
            • Dimensions (H x W x D): 1.75" x 19" x 7.25"
            • Weight: 5.63 lbs
Main Intercom Station with Power Supply, 4 Channel
Clear-Com MS704 Main Intercom Station with Power Supply, 4 Channel
The 704 series is Clear-Com's most advanced party-line intercom system. Each station is a four-channel intercom with superior audio and versatile channel access to provide unmatched communication flexibility. All front-panel controls are ...
2 Channel Main Intercom Station with Power Supply
Clear-Com MS-702 2 Channel Main Intercom Station with Power Supply
Clear-Com's MS-702 is a one-rack-space, two-channel main station with a regulated 1.2-amp "fail-safe" power supply, individual channel short-circuit protection, and a versatile intercom monitoring system. It supports two intercom channels ...

Clear-Com TW12C
Encore CC/RTS System Interface

OUR PART #  TW12C

Product Information:

Clear-Com's TW-12C intercom system interface is designed for connecting one intercom system to another, without compromising the audio quality of either system.

Transparent Isolation Between Systems
The unique TW-12C completely eliminates hums and buzzes caused by ground loops. The TW-12C compensates not only for level differences between systems, but for varying impedances caused by transformers and capacitance on the lines.

The TW-12C provides an electrically isolated interface between the two intercom systems. Either "side" of the interface can connect to a Clear-Com intercom system or an RTS intercom system, allowing Clear-Com-to-Clear-Com, Clear-Com-to-RTS, and RTS-to-RTS combinations. In addition, the TW-12C passes through and translates "call" signals, Clear-Com-to-RTS and vice versa.

The interface consists of two identical, 2-wire-to-4-wire hybrid networks which break the ground loops that occur when two systems are run from separate power sources. The audio paths are transformer-coupled and the signaling circuits are opto-isolated.

Fast, Easy & Accurate Setup
The operator can quickly set up the TW-12C by using a standard intercom headset and the TW-12C's built-in setup tone. The TW-12C is capable of a range of null adjustments, allowing it to adapt to a wide variety of line conditions, line lengths, and impedances.

The TW-12C provides each side of the system with null adjustment controls that allow adjustment even when the system is operating. The rear panel of the TW-12C contains a pair of 3-pin XLR connectors (one male, one female) for each side of the interface.

Call Signal Translation
The TW-12C interface receives "Call" signaling in the appropriate form (DC level for Clear-Com, tone for RTS), decodes it, and passes it to the other side of the interface, via an optical coupler. The receiving side of the interface sends the signal appropriate for the connected intercom.

Power
Each side of the TW-12C is powered directly by the intercom system to which it is connected. The unit draws about the same amount of power as a belt-pack. If either system is disconnected, the power loss immediately shuts down the associated electronics, eliminating any unwanted noises on the operating intercom side. The TW-12C front panel provides an LED power indicator for each side of the interface.

Clear-Com TW12C Features:

  • Eliminates grounding problems between intercom systems
  • Matches gain between systems
  • Provides system isolation for: Clear-Com toClear-Com; Clear-Com to RTS; RTS to RTS
  • Passes through and translates signaling
  • Provides superior hybrid nulling - up to 40dB
  • Setup tone allows adjustment during operation
  • Powered from connected systems
  • Uses just one rack space

Clear Com Format

  • Line Characteristics
    • Max Level Before Clipping :>=3dBu
    • Impedance: >=10Kohms
    • < /UL>< LI>Signalling
      • Receive: <=4 VDC
      • Send: >=11VDC

    RTS Format

    • Line Characteristics
      • Max Level Before Clipping :>=5dBu
      • Impedance: >=10Kohms
      • < /UL>
      • SignallingTone
        • Send frequency: 20kHz ±100Hz
        • Receive frequency:20kHz ±500Hz
        • Send level: >=-6dBu
        • Receive level: <=-25dBu

      Clear-Com TW12C Specifications:

      • Frequency response
        • Party Line- Party Line: 200-8KHz
      • Distortion
        • Party Line - PartyLine: <=0.2%
        • < /UL>
        • Max Gain
          • ClearCom - RTS: >=9dB
          • ClearCom - ClearCom:>=4dB
          • RTS - ClearCom: >=-1dB
          • RTS -RTS: >=4dB
          • < /UL>
          • Min Gain
            • ClearCom - RTS: <=1dB
            • ClearCom - ClearCom:<=-4dB
            • RTS - ClearCom: <=-9dB
          • Power Requirements
            • Input Voltage Range: 20-30VDC
            • Input Current (average):<=50mA
            • < /UL>
            • Rear Panel Connectors
              • (2) XLR3M (1 per channel)
              • (2) XLR3F (1 per channel)
            • Front Panel Connectors
              • Headset: (1) XLR4M
              • TS1 Earphone:(1) 3.5mm Jack Socket
            • Front Panel Controls and Indicators
              • Power: (2) Green LED (1 perchannel)
              • Null Test Button : (2) Buttons (1 per channel)
              • Gain LevelAdjust: (2) Controls (1 per channel)
              • Null Adjust: (6) Controls (3 perchannel)
              • Connection Type Switch: (2) Switches (1 per channel)
              • Pin Connection Select Switch: (2) Switches (1 per channel)
            • Dimensions (H x W x D): 1.75" x 19" x 7.25"
            • Weight: 5.63 lbs
Main Intercom Station with Power Supply, 4 Channel
Clear-Com MS704 Main Intercom Station with Power Supply, 4 Channel
The 704 series is Clear-Com's most advanced party-line intercom system. Each station is a four-channel intercom with superior audio and versatile channel access to provide unmatched communication flexibility. All front-panel controls are ...
2 Channel Main Intercom Station with Power Supply
Clear-Com MS-702 2 Channel Main Intercom Station with Power Supply
Clear-Com's MS-702 is a one-rack-space, two-channel main station with a regulated 1.2-amp "fail-safe" power supply, individual channel short-circuit protection, and a versatile intercom monitoring system. It supports two intercom channels ...
Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM