RTS CM-300L A4F
Console Mount 2-Channel Intercom User Station with A4F Headphone Connector

OUR PART #  CM300L/A4F


RTS' CM-300L is a console mount, two-channel intercom user station.  The user station is designed to be used in a full duplex, conference line intercom system.

Features:

  • The volume control on the CM-300L has a wide range to compensate for: user hearing differences, ambient noise variation, variations in headset / handset sensitivity, and variations in voice.  The volume control in the CM-300L reduces distortion by driving the headphone amplifier only as much as needed.
  • In normal system operation, one or more users talk and the others listen.  A microphone switch on each station allows the talker's microphone to be enabled and allows the listeners to keep their microphones disabled.  In this condition, speech intelligibility is enhanced since background noise from other microphones is not present.  On the Model CM-300L, a toggle switch turns the microphone on.
  • A channel selector switch allows a choice of two (optionally three) channels. When the switch is on the "1" position the station talks and listens on channel 1, on the "2" position, to channel 2.
  • Pushing the Call Light button transmits a call signal to all other units on the channel selected by the channel selector switch.  A call signal on this channel will cause the call light push button to flash.  The flash rate is 2 to 5 times a second.  The call signal itself is a 20 kilohertz signal.

Specifications:

  • Input DC Voltage:
    TW Mode: 18 to 35 volts DC
    LP Option: 15 to 35 volts DC
    Battery: 12 to 35 volts DC (reduced performance)
  • DC Current Drawing from TW Line (Note: LP Option draws no current from TW line):
    Quiescent:
    - CM-300/RM-300: 23 milliamperes ±10%
    - CM-300/RM-300L: 33 milliamperes ±10%
    Operating 25 Ohm headphones:
    - CM-300/RM-300: 37 milliamperes ±10%
    - CM-300/RM-300L: 45 milliamperes ±10%
    Operating 25 Ohm headphones + Call Light:
    - CM-300/RM-300: 60 milliamperes ±10%
  • Impedance Across Line: 10,000 ohms, minimum
  • Operating Temperature: 0°C to 60°C
  • Storage Temperature: -40°C to 85°C
  • Operating and Storage Humidity: 5% to 95% non-condensing
  • Noise Contribution:
    One Unit: -75 dBu
    Ten Units: -67 dBu
  • Microphone Preamplifier:
    Input Impedance: 470 ohms/dynamic mic
    Source Impedance: 200 ohms, nominal
    Maximum Input Level: 150 millivolts
    Frequency Response: 100 hertz to 10 kilohertz ±3 dB (-54 dBu input)
    Limiter Range: 30 dB
    Carbon Mic Excitation Current: 10 millliamperes, nominal
  • Current Source:
    Transfer Ratio: 3.3 milliamperes/volt=3.3 millisiemens
    Output: ±5 milliamperes into 200 ohms = ±1 volt peak, nominal
  • Headphone Amplifier:
    Voltage Gain: 34 dB
    Output Voltage: 8 volts peak-to-peak into 25-1/2
    Output Power: 1/2 watt peak into 25 ohms
    Frequency Response: 150 hertz to 8 kilohertz ±3dB
    Headphone Impedance Range: 25 to 600 O (600 to 2000 with reduced levels)
    Note: Do not use headphones with impedance less than 25 O.
    Sidetone Adjustment Range: -20dB to full on
  • Call-Light:
    Signaling Frequency: 20,000 hertz ±100 hertz
    Flashing Rate: 5 hertz ±2 hertz
  • Auxiliary Connections:
    Headset Connector
    - Dynamic Microphone: XLR type 4-pin female
    - Carbon Microphone: 1/4"standard phone jack, 3-circuit
    Live Connection
    - Input: XLR type 3-pin female
    - Loop/External: XLR type 3-pin female
    Mechanical:
    - Dimensions: 2.75" (69.9mm) high, 6.25" (158.75 mm) wide, 6.4" (162.6mm) deep
    - Weight: 1.2 lbs (0.55 kg)
    - Finish: Front Panel: Light Gray Enamel Paint
    - Federal Standard 595A Color#26492
    - Chassis: Gold Iridite over aluminum
Single-sided Mediumweight Headset with A4M Connector
Telex PH1R Single-sided Mediumweight Headset with A4M Connector
Medium-weight single muff headset with foam filled cushions offers a light feel with moderate isolation from ambient noise. Dynamic noise canceling mic is easily positioned with unique continuously adjustable ball joint. Telex PH1R ...
Single-sided Lightweight Headset, A4M Connector
Telex PH-88R Single-sided Lightweight Headset, A4M Connector
Telex's PH-88R is a super light-weight single muff headset with dynamic noise canceling microphone. Semi-rigid, fully adjustable gooseneck mic boom for precise positioning. High quality wide band earphones with moleskin covering for better ...
Dual-sided Medium-weight Passive Noise Reduction Headset, A4M Connector
Telex HR2R-300534-001 Dual-sided Medium-weight Passive Noise Reduction Headset, A4M Connector
The HR-2 is a dual-sided, medium-weight passive noise reduction headset with dynamic noise canceling microphone. the headset has a noise reduction rating of 21 dB; suitable for use in a moderately noisy environment. The ergonomic headband ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual-sided Mediumweight Headset, A4M Connector
Telex PH2R-64437-102 Dual-sided Mediumweight Headset, A4M Connector
The PH-2 and PH-2R is a medium-weight dual muff mono headset with foam filled cushions offers a light feel with moderate isolation from ambient noise. Dynamic noise canceling mic is easily positioned with unique continuously adjustable ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Single Headset with Mic
Telex PH88E-R Single Headset with Mic
Lightweight, single-sided headset with a flexible dynamic boom microphone. 150 ohm earphone with a 12 ft (3.6m) coiled cord and an A4M connector.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual Sided Headset with Mic and A4M Connector
Telex PH44R-300853-401 Dual Sided Headset with Mic and A4M Connector
Lightweight, dual-sided professional headphones with a flexible dynamic boom microphone. 150 ohm earhpones with a 6 ft (1.8m) cord, and an A4M connector.

Usually ships in 7-14 business days.
Need it sooner? Call us!
25 Ft XLR Intercom Cable in Black
Telex ME-25 25 Ft XLR Intercom Cable in Black
The Telex ME-25 is a 25 ft (7.6 m) Super-Flex cable with Male and Female 3-pin XLR connectors.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

RTS CM-300L A4F
Console Mount 2-Channel Intercom User Station with A4F Headphone Connector

OUR PART #  CM300L/A4F

Product Information:

RTS' CM-300L is a console mount, two-channel intercom user station.  The user station is designed to be used in a full duplex, conference line intercom system.

Features:

  • The volume control on the CM-300L has a wide range to compensate for: user hearing differences, ambient noise variation, variations in headset / handset sensitivity, and variations in voice.  The volume control in the CM-300L reduces distortion by driving the headphone amplifier only as much as needed.
  • In normal system operation, one or more users talk and the others listen.  A microphone switch on each station allows the talker's microphone to be enabled and allows the listeners to keep their microphones disabled.  In this condition, speech intelligibility is enhanced since background noise from other microphones is not present.  On the Model CM-300L, a toggle switch turns the microphone on.
  • A channel selector switch allows a choice of two (optionally three) channels. When the switch is on the "1" position the station talks and listens on channel 1, on the "2" position, to channel 2.
  • Pushing the Call Light button transmits a call signal to all other units on the channel selected by the channel selector switch.  A call signal on this channel will cause the call light push button to flash.  The flash rate is 2 to 5 times a second.  The call signal itself is a 20 kilohertz signal.

Specifications:

  • Input DC Voltage:
    TW Mode: 18 to 35 volts DC
    LP Option: 15 to 35 volts DC
    Battery: 12 to 35 volts DC (reduced performance)
  • DC Current Drawing from TW Line (Note: LP Option draws no current from TW line):
    Quiescent:
    - CM-300/RM-300: 23 milliamperes ±10%
    - CM-300/RM-300L: 33 milliamperes ±10%
    Operating 25 Ohm headphones:
    - CM-300/RM-300: 37 milliamperes ±10%
    - CM-300/RM-300L: 45 milliamperes ±10%
    Operating 25 Ohm headphones + Call Light:
    - CM-300/RM-300: 60 milliamperes ±10%
  • Impedance Across Line: 10,000 ohms, minimum
  • Operating Temperature: 0°C to 60°C
  • Storage Temperature: -40°C to 85°C
  • Operating and Storage Humidity: 5% to 95% non-condensing
  • Noise Contribution:
    One Unit: -75 dBu
    Ten Units: -67 dBu
  • Microphone Preamplifier:
    Input Impedance: 470 ohms/dynamic mic
    Source Impedance: 200 ohms, nominal
    Maximum Input Level: 150 millivolts
    Frequency Response: 100 hertz to 10 kilohertz ±3 dB (-54 dBu input)
    Limiter Range: 30 dB
    Carbon Mic Excitation Current: 10 millliamperes, nominal
  • Current Source:
    Transfer Ratio: 3.3 milliamperes/volt=3.3 millisiemens
    Output: ±5 milliamperes into 200 ohms = ±1 volt peak, nominal
  • Headphone Amplifier:
    Voltage Gain: 34 dB
    Output Voltage: 8 volts peak-to-peak into 25-1/2
    Output Power: 1/2 watt peak into 25 ohms
    Frequency Response: 150 hertz to 8 kilohertz ±3dB
    Headphone Impedance Range: 25 to 600 O (600 to 2000 with reduced levels)
    Note: Do not use headphones with impedance less than 25 O.
    Sidetone Adjustment Range: -20dB to full on
  • Call-Light:
    Signaling Frequency: 20,000 hertz ±100 hertz
    Flashing Rate: 5 hertz ±2 hertz
  • Auxiliary Connections:
    Headset Connector
    - Dynamic Microphone: XLR type 4-pin female
    - Carbon Microphone: 1/4"standard phone jack, 3-circuit
    Live Connection
    - Input: XLR type 3-pin female
    - Loop/External: XLR type 3-pin female
    Mechanical:
    - Dimensions: 2.75" (69.9mm) high, 6.25" (158.75 mm) wide, 6.4" (162.6mm) deep
    - Weight: 1.2 lbs (0.55 kg)
    - Finish: Front Panel: Light Gray Enamel Paint
    - Federal Standard 595A Color#26492
    - Chassis: Gold Iridite over aluminum
Single-sided Mediumweight Headset with A4M Connector
Telex PH1R Single-sided Mediumweight Headset with A4M Connector
Medium-weight single muff headset with foam filled cushions offers a light feel with moderate isolation from ambient noise. Dynamic noise canceling mic is easily positioned with unique continuously adjustable ball joint. Telex PH1R ...
Single-sided Lightweight Headset, A4M Connector
Telex PH-88R Single-sided Lightweight Headset, A4M Connector
Telex's PH-88R is a super light-weight single muff headset with dynamic noise canceling microphone. Semi-rigid, fully adjustable gooseneck mic boom for precise positioning. High quality wide band earphones with moleskin covering for better ...
Dual-sided Medium-weight Passive Noise Reduction Headset, A4M Connector
Telex HR2R-300534-001 Dual-sided Medium-weight Passive Noise Reduction Headset, A4M Connector
The HR-2 is a dual-sided, medium-weight passive noise reduction headset with dynamic noise canceling microphone. the headset has a noise reduction rating of 21 dB; suitable for use in a moderately noisy environment. The ergonomic headband ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual-sided Mediumweight Headset, A4M Connector
Telex PH2R-64437-102 Dual-sided Mediumweight Headset, A4M Connector
The PH-2 and PH-2R is a medium-weight dual muff mono headset with foam filled cushions offers a light feel with moderate isolation from ambient noise. Dynamic noise canceling mic is easily positioned with unique continuously adjustable ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Single Headset with Mic
Telex PH88E-R Single Headset with Mic
Lightweight, single-sided headset with a flexible dynamic boom microphone. 150 ohm earphone with a 12 ft (3.6m) coiled cord and an A4M connector.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Dual Sided Headset with Mic and A4M Connector
Telex PH44R-300853-401 Dual Sided Headset with Mic and A4M Connector
Lightweight, dual-sided professional headphones with a flexible dynamic boom microphone. 150 ohm earhpones with a 6 ft (1.8m) cord, and an A4M connector.

Usually ships in 7-14 business days.
Need it sooner? Call us!
25 Ft XLR Intercom Cable in Black
Telex ME-25 25 Ft XLR Intercom Cable in Black
The Telex ME-25 is a 25 ft (7.6 m) Super-Flex cable with Male and Female 3-pin XLR connectors.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM