Radio Design Labs ST-LCR3
Dual Relay

OUR PART #  STLCR3


Radio Design Labs' ST-LCR3 is ideally suited to applications where momentary pulses are needed from a single control signal. The module provides a momentary pulse when a logic signal at its input first becomes active. A separate momentary pulse is provided when the logic signal at the module input becomes inactive.

Two logic inputs are available on the ST-LCR3. Either of these inputs may be used. Terminal 1 is internally pulled high to +5 Vdc. This input becomes active when an external closure or open-collector pulls the terminal to ground. The external switching device does not need to pull the terminal high, however the terminal may be pulled high with any voltage from +3.3 Vdc to +24 Vdc without any risk of damage to the ST-LCR3 input. Terminal 3 is internally pulled to ground. This input becomes active when an external closure or logic device applies a positive voltage from +3.3 Vdc to + 24 Vdc.

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

When the input being used first becomes active the START PULSE output from the module is triggered. When the input first becomes inactive (after first being active) the END PULSE output from the module is triggered. Both the start and end pulses have a nominal duration of 250 ms.

Each pulse output provides both an open-collector SLAVE terminal and relay contacts. The SLAVE terminal may be used to control other RDL modules and a variety of other equipment. The relay contacts may be used to control modules or equipment that do not operate from open-collector control.

Features:

  • Pulse at the Start of a Logic Signal
  • Pulse at the End of a Logic Signal
  • Relay Contact and Open-Collector Pulse
  • Active High or Active Low Inputs
  • Input Control Voltage From 3.3 to 24 Vdc
  • Control from Switch, Pushbutton, or Logic Circuits

Typical Performance:

  • Inputs (2): Logic High or Logic Low (Low = ground, High =3.3 Vdc to 24 Vdc) < /FONT >
  • Outputs (2): Open collector @ 25 mA suitable to drive indicators or slave LCRs.
  • Maximum Switching Power: 60 W (220 Vdc, 125 Vac, 2 A)
  • Power Requirement: GROUND-REFERENCED, 24 to 33 Vdc @ 100 mA (assuming 20 mA max load at SLAVE output)
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs ST-LCR3
Dual Relay

OUR PART #  STLCR3

Product Information:

Radio Design Labs' ST-LCR3 is ideally suited to applications where momentary pulses are needed from a single control signal. The module provides a momentary pulse when a logic signal at its input first becomes active. A separate momentary pulse is provided when the logic signal at the module input becomes inactive.

Two logic inputs are available on the ST-LCR3. Either of these inputs may be used. Terminal 1 is internally pulled high to +5 Vdc. This input becomes active when an external closure or open-collector pulls the terminal to ground. The external switching device does not need to pull the terminal high, however the terminal may be pulled high with any voltage from +3.3 Vdc to +24 Vdc without any risk of damage to the ST-LCR3 input. Terminal 3 is internally pulled to ground. This input becomes active when an external closure or logic device applies a positive voltage from +3.3 Vdc to + 24 Vdc.

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

When the input being used first becomes active the START PULSE output from the module is triggered. When the input first becomes inactive (after first being active) the END PULSE output from the module is triggered. Both the start and end pulses have a nominal duration of 250 ms.

Each pulse output provides both an open-collector SLAVE terminal and relay contacts. The SLAVE terminal may be used to control other RDL modules and a variety of other equipment. The relay contacts may be used to control modules or equipment that do not operate from open-collector control.

Features:

  • Pulse at the Start of a Logic Signal
  • Pulse at the End of a Logic Signal
  • Relay Contact and Open-Collector Pulse
  • Active High or Active Low Inputs
  • Input Control Voltage From 3.3 to 24 Vdc
  • Control from Switch, Pushbutton, or Logic Circuits

Typical Performance:

  • Inputs (2): Logic High or Logic Low (Low = ground, High =3.3 Vdc to 24 Vdc) < /FONT >
  • Outputs (2): Open collector @ 25 mA suitable to drive indicators or slave LCRs.
  • Maximum Switching Power: 60 W (220 Vdc, 125 Vac, 2 A)
  • Power Requirement: GROUND-REFERENCED, 24 to 33 Vdc @ 100 mA (assuming 20 mA max load at SLAVE output)
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM