Radio Design Labs ST-SH2
Stereo Headphone Amplifier

OUR PART #  STSH2


Radio Design Labs' ST-SH2 is used in applications requiring headphones of any impedance to be driven from consumer or professional audio sources. For fixed level installations not requiring user volume control, the ST-SH2 is wired to the audio source and to a headphone jack. Frequently, it is desirable to mount a volume knob by the headphone jack. The LEVEL ADJUST terminals (L) and (R) may be wired to the respective wipers of a stereo 10 kO potentiometer to provide volume adjustment. It is recommended that the ST-SH2 be located less than 39" (1 m) from the jack and volume control.

The exceptional low noise (better than 100 dB below operating level), low distortion, audio clarity and excellent crosstalk performance makes this module ideally suited to a wide variety of demanding audio applications. Use this module in conjunction with other RDL® modules as part of a high quality, flexible audio/ video system.

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

Features:

  • Stereophonic Headphone Amplifier
  • Provision for External Stereo Level Control
  • Balanced or Unbalanced Input
  • Bridge a Line and Feed Headsets
  • Amplifier To Drive High or Low Impedance Headsets

Specifications:

  • Inputs (2): 10 kO balanced or unbalanced, bridging
  • Input Signal: -20 dBu (-22 dBV) to +6 dBu (for normal output level: +4 dBu, 100 ù) -10 dBu to +16 dBu (for 250 mW, 8 O output)
  • Output Load Impedance: 8 O to 5 kO (drives low or high impedance headphones)
  • Output Signal (normal rated): +4 dBu into 100 O
  • Output Signal (maximum): 250 mW into 8 O, 20 Vp-p into 2 kO
  • THD+N: < 0.005% (0.0015% typical @ 1 kHz)
  • Frequency Response: 20 Hz to 40 kHz (+/- 0.25 dB)
  • Noise: < -100 dB below normal operating level
  • Total Dynamic Range: > 115 dB
  • Gain: Adjustable from -2 to 24 dB
  • CMRR: > 50 dB at 100 Hz
  • Crosstalk: < -65 dB (10 Hz to 20 kHz); < -80 dB @ 1 kHz
  • Power Requirement: GROUND-REFERENCED, 24 to 33 Vdc @ 175 mA
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs ST-SH2
Stereo Headphone Amplifier

OUR PART #  STSH2

Product Information:

Radio Design Labs' ST-SH2 is used in applications requiring headphones of any impedance to be driven from consumer or professional audio sources. For fixed level installations not requiring user volume control, the ST-SH2 is wired to the audio source and to a headphone jack. Frequently, it is desirable to mount a volume knob by the headphone jack. The LEVEL ADJUST terminals (L) and (R) may be wired to the respective wipers of a stereo 10 kO potentiometer to provide volume adjustment. It is recommended that the ST-SH2 be located less than 39" (1 m) from the jack and volume control.

The exceptional low noise (better than 100 dB below operating level), low distortion, audio clarity and excellent crosstalk performance makes this module ideally suited to a wide variety of demanding audio applications. Use this module in conjunction with other RDL® modules as part of a high quality, flexible audio/ video system.

NOTE: Radio Design Labs' PS-24AS power supply is NOT included but is required in order to power this product.  Please see the "Accessories" tab or click here for more information on the PS-24AS power supply.

Features:

  • Stereophonic Headphone Amplifier
  • Provision for External Stereo Level Control
  • Balanced or Unbalanced Input
  • Bridge a Line and Feed Headsets
  • Amplifier To Drive High or Low Impedance Headsets

Specifications:

  • Inputs (2): 10 kO balanced or unbalanced, bridging
  • Input Signal: -20 dBu (-22 dBV) to +6 dBu (for normal output level: +4 dBu, 100 ù) -10 dBu to +16 dBu (for 250 mW, 8 O output)
  • Output Load Impedance: 8 O to 5 kO (drives low or high impedance headphones)
  • Output Signal (normal rated): +4 dBu into 100 O
  • Output Signal (maximum): 250 mW into 8 O, 20 Vp-p into 2 kO
  • THD+N: < 0.005% (0.0015% typical @ 1 kHz)
  • Frequency Response: 20 Hz to 40 kHz (+/- 0.25 dB)
  • Noise: < -100 dB below normal operating level
  • Total Dynamic Range: > 115 dB
  • Gain: Adjustable from -2 to 24 dB
  • CMRR: > 50 dB at 100 Hz
  • Crosstalk: < -65 dB (10 Hz to 20 kHz); < -80 dB @ 1 kHz
  • Power Requirement: GROUND-REFERENCED, 24 to 33 Vdc @ 175 mA
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...

Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.

Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.

Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM