Radio Design Labs ST-PD5U
Power Supply Distributor for up to 5 Modules

OUR PART #  STPD5U

Log In for price!

Don't have an account? Apply today!

Radio Design Labs' ST-PD5U is the ideal choice where power distribution from a current-limited switching power supply is needed. It is suitable for powering up to five modules from a single power supply. The current limiting circuitry in many switching power supplies will cause the supply to shut down upon power-up when a high current capacitive load is connected. Upon application of power, the ST-PD5U ramps the voltage up, charging any load capacitance as quickly as possible, then switching full voltage to the load. If reverse polarity is connected to the input, the ST-PD5U disconnects the load until the condition is corrected.

In system design, various modules are frequently operated from a single power supply. Good engineering practice requires that the power wiring to each module originate at the power supply output. The ST-PD5U serves as the power source for each of five modules. A single ST-PD5U can provide power to RDL’s floating modules. A separate ST-PD5U can provide power to ground-referenced modules. (Do not attempt to intermix floating and ground-referenced modules from a single ST-PD5U.) Note: If using a linear power supply, distribute the voltage to multiple modules using an RDL ST-PD5

Wherever power distribution from a switching power supply is needed, the ST-PD5U is the ideal choice. Use the ST-PD5U combined with other RDL RACK-UP®, STICK-ON®, Flat-Pak™ or TX™ series products as part of a complete audio/video system

Features:

  • Distribution of 24 Vdc Power
  • Soft-Start from Switching Supply
  • Distribution of dc Power
  • Up to 5 Power Distribution Points
  • Voltage Presence Indication
  • Reverse Voltage Protection

Typical Performance:

  • Input/Output Voltage: 24 Vdc @ 2 A (Intended for use with current limited switching supply)
  • Number of Outputs (5): Total load current must not exceed 2 A
  • Indicators (2): POWER LED and FAULT LED
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...
Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Radio Design Labs ST-PD5U
Power Supply Distributor for up to 5 Modules

OUR PART #  STPD5U

Product Information:

Radio Design Labs' ST-PD5U is the ideal choice where power distribution from a current-limited switching power supply is needed. It is suitable for powering up to five modules from a single power supply. The current limiting circuitry in many switching power supplies will cause the supply to shut down upon power-up when a high current capacitive load is connected. Upon application of power, the ST-PD5U ramps the voltage up, charging any load capacitance as quickly as possible, then switching full voltage to the load. If reverse polarity is connected to the input, the ST-PD5U disconnects the load until the condition is corrected.

In system design, various modules are frequently operated from a single power supply. Good engineering practice requires that the power wiring to each module originate at the power supply output. The ST-PD5U serves as the power source for each of five modules. A single ST-PD5U can provide power to RDL’s floating modules. A separate ST-PD5U can provide power to ground-referenced modules. (Do not attempt to intermix floating and ground-referenced modules from a single ST-PD5U.) Note: If using a linear power supply, distribute the voltage to multiple modules using an RDL ST-PD5

Wherever power distribution from a switching power supply is needed, the ST-PD5U is the ideal choice. Use the ST-PD5U combined with other RDL RACK-UP®, STICK-ON®, Flat-Pak™ or TX™ series products as part of a complete audio/video system

Features:

  • Distribution of 24 Vdc Power
  • Soft-Start from Switching Supply
  • Distribution of dc Power
  • Up to 5 Power Distribution Points
  • Voltage Presence Indication
  • Reverse Voltage Protection

Typical Performance:

  • Input/Output Voltage: 24 Vdc @ 2 A (Intended for use with current limited switching supply)
  • Number of Outputs (5): Total load current must not exceed 2 A
  • Indicators (2): POWER LED and FAULT LED
Rackmount System for 12 Stick-On Units
Radio Design Labs STR-19A Rackmount System for 12 Stick-On Units
Radio Design Labs' STR-19A Racking System holds up to 12 STICK-ONs in a 19" rack and only occupies two rack spaces.
Stick-On Mounting Rack for 10 Units
Radio Design Labs SR-10 Stick-On Mounting Rack for 10 Units
Radio Design Labs' STR-10 Racking System holds up to 10 STICK-ON units.  It holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or the top (depending on where the adjustment is located on ...
24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs PS-24AS 24 VDC 500mA Switching Power Supply, North American Model
Radio Design Labs' PS-24AS is a 24 VDC/500 mA switching power supply with a North American AC plug. Compatible with various RDL products.Radio Design Labs PS-24AS Specifications: Input: 100 to 240 VAC Output: 24 Vdc, 500 mA (UL, ...
Din Rail Adaptor for STICK-ON
Radio Design Labs DRA-35S Din Rail Adaptor for STICK-ON
The DRA-35S is a 35 mm DIN rail mounting bracket that provides positive mounting for any RDL STICK-ON® module. The oblique mounting angle of the DRA-35S allows an installer to mount several STICK-ON modules to a single DIN rail. Access to ...
Mounting Kit for STICK-ON, TX, or Rack-Up module
Radio Design Labs MB1-RDL Mounting Kit for STICK-ON, TX, or Rack-Up module
Two mounting brackets mounts a STICK-ON, TX, or Rack-Up module to a flat surface.
Rackmount Kit for 10 Stick-On Units
Radio Design Labs STR-19B Rackmount Kit for 10 Stick-On Units
Radio Design Labs' STR-19B Racking System holds up to 10 STICK-ON unitss in a 19 inch rack and only occupies two rack spaces. The STR-19B holds STICK-ONs at an angle allowing for control adjustment from either the edge of a STICK-ON, or ...
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Frame for Stick/TX
Radio Design Labs SR-4 Mounting Frame for Stick/TX
Radio Design Labs' SR-4 is a universal module chassis that can mount to a backboard, wall or nearly any other support. It provides mounting for 4 STICK-ON power amplifiers or 7 standard STICK-ON modules. TX ™ modules may also be mounted. ...
Usually ships in 7-14 business days.
Need it sooner? Call us!
STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs SR-12A STICK-ON Series 19"W Mounting Rack for up to12 Modules
Radio Design Labs' SR-12A chassis can be mounted in a rack or on a backboard to provide mounting of 12 STICK-ONs.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Strip for STICK-ON Units
Radio Design Labs Smk 12 Mounting Strip for STICK-ON Units
The SMK-12 allows removable surface (up to 6 units) or edge (typically 12, max. 16) mounting of STICK-ON units. They can be fastened to its surface using screws or adhesive foam pads.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Mounting Bracket for STICK-ON Modules
Radio Design Labs ST-RRB1 Mounting Bracket for STICK-ON Modules
Radio Design Labs' ST-RRB1 mounting kit contains a bracket to attach a STICK-ON module to a rear rack rail or to any flat surface. The module slides into the holder and snaps into position. The module may easily be removed.
Usually ships in 7-14 business days.
Need it sooner? Call us!
Detachable Terminal Block
Radio Design Labs Dtb Rdl Detachable Terminal Block
Use DTB's to quickly detach and reattach wiring harness to STICK-ON units.
Usually ships in 7-14 business days.
Need it sooner? Call us!

Click to download

Add to Cart

We're sorry, only of this item available



Call a Sales Pro at for more information

Serving Contractors, Dealers, and Installers Since 1977

Contact: 1-800-828-0509 / Hours: Mon - Fri 7:00AM - 7:00PM